Serpentine belt also known as drive belt or Accessory belt.
Belts are made of reinforced synthetic and/or hard rubber, belts are usually v-channeled or ribbed serpentine They're used to drive accessories including the alternator, water pump, AC compressor, power steering, air pump, vacuum pump and injector pump. They're usually driven by the engine's crankshaft pulley and are fully adjustable by tensioners or idlers that follow or track the surface of the belt.
The diagrams are for both,with and without AC models.The belt tension should be absolutely right.Not too loose or over tight.Adjust the belt tensioner correctly.Also inspect that all pulleys from where belt routes ,are proper and not worn out.
Belt routing all depends on car model and engine.Its routing goes on how many pulleys it has.
Start by studying the old belt’s routing, which should be easy if the belt is still in place. But it’s probably not so easy to spot if the belt is wadded up like macramé next to the a/c compressor’s mounting bracket. Fear not: There should be a belt-routing placard under the hood. If the car has had bodywork or been repainted, the placard might have been covered. Look in the owner’s manual; there’s usually a routing diagram. With a half-dozen pulleys to choose from, it’s possible, sometimes, to install the belt the wrong way. It might look right, but spinning the a/c compressor or water pump backwards isn’t good. If the belt is hard to install or seems to fit poorly, you may have it routed incorrectly. Don’t freak—sometimes the water pump is driven by the flat, back side of the belt. Any pulley that has grooves on it is intended to contact the grooved side of the belt. If you need to, sketch the correct routing down before you remove the old belt. As a last resort, check the shop manual.
This details will help you.
----------
If you need any car belt diagram,just check the list mentioned below:-----
Timing belt routing diagrams for cars and trucks?
Drive belt routing diagrams for cars and trucks?
How to replace Timing Belt Cover on Acura Car models?
How to replace Timing Belt and Sprockets on Acura Car models?
How to replace Timing Belt on Audi and VW car models?
How to replace Timing Belt Cover on Audi and VW car models?
How to replace Timing Belt Sprockets on Audi car models?
Replacing Timing belt on Toyota Tercel?
How the timing marks on valve pulleys line up with crank on 1997 Dodge Intrepid?
Timing belt Replacing procedure for Daewoo Nubira?
Replace Drive Belt on 2003 Hyundai Tiburon?
http://carbeltrouting.blogspot.com/2011/12/replace-drive-belt-on-2003-hyundai.html
Serpentine
2005 Toyota Tacoma serpentine belt diagram?
Ford Super Duty F 450 drive belt routing diagram?
2004 Ford Truck F450 Super Duty P/U 4WD 6.0L Turbo Diesel 8cyl Serpentine belt routing?
2006 Ford Mustang Serpentine belt routing?
Jaguar S-Type Belt routing diagram?
Drive Belt replacing on 2001 hyundai xg300?
2002 FORD TRUCK WINDSTAR Serpentine belt routing?
Fan belt routing diagram for 2004 Volkswagen Jetta?
Chevy Duramax Belt routing?
1992 Ford Aerostar Power steering and Alternator belt routing diagram?
Jeep Wrangler drive belt diagram?
http://carbeltrouting.blogspot.com/2011/12/jeep-wrangler-drive-belt-diagram.html
Belts are made of reinforced synthetic and/or hard rubber, belts are usually v-channeled or ribbed serpentine They're used to drive accessories including the alternator, water pump, AC compressor, power steering, air pump, vacuum pump and injector pump. They're usually driven by the engine's crankshaft pulley and are fully adjustable by tensioners or idlers that follow or track the surface of the belt.
The diagrams are for both,with and without AC models.The belt tension should be absolutely right.Not too loose or over tight.Adjust the belt tensioner correctly.Also inspect that all pulleys from where belt routes ,are proper and not worn out.
Belt routing all depends on car model and engine.Its routing goes on how many pulleys it has.
Start by studying the old belt’s routing, which should be easy if the belt is still in place. But it’s probably not so easy to spot if the belt is wadded up like macramé next to the a/c compressor’s mounting bracket. Fear not: There should be a belt-routing placard under the hood. If the car has had bodywork or been repainted, the placard might have been covered. Look in the owner’s manual; there’s usually a routing diagram. With a half-dozen pulleys to choose from, it’s possible, sometimes, to install the belt the wrong way. It might look right, but spinning the a/c compressor or water pump backwards isn’t good. If the belt is hard to install or seems to fit poorly, you may have it routed incorrectly. Don’t freak—sometimes the water pump is driven by the flat, back side of the belt. Any pulley that has grooves on it is intended to contact the grooved side of the belt. If you need to, sketch the correct routing down before you remove the old belt. As a last resort, check the shop manual.
This details will help you.
----------
If you need dis-assembly or replacement instructions for any other auto/car part, or you want to ask question related to your car/truck jeep problem then please leave the comment with your details, so I can provide you the required instructions and solutions.
If you need any car belt diagram,just check the list mentioned below:-----
For all types of
Timing belt routing diagrams for cars and trucks?
Click the link below:---
For all types of
Drive belt routing diagrams for cars and trucks?
Click the link below:---
No comments:
Post a Comment